Coax Cable Environmental: damp; moisture; sunlight

Coax cable is affected by environmental issues including moisture, damp, sunlight and more.

Home » Antennas & Propagation » this page

Coax Tutorial Includes:
Coax feeder Coax specifications overview Coax impedance Coax loss / attenuation Coax power rating Coax velocity factor Coax environmental Coax installation tips Coax cable types Tips for choosing right coax cable Buying TV coax: points to note

RF coaxial cable is very robust bust consideration must be given when using it is a variety of environments to ensure that it is able to withstand them without any undue degradation in performance.

As coaxial cable is normally installed and maintained in position for long periods of time, it is necessary to ensure that the RF cable environmental constraints are taken into consideration.

It is necessary to understand the coax cable environmental aspects and then plan any installations accordingly.

Coax cable feeder — Typical coax cable feeder

Coax cable environmental factors

There are many factors that affect coax cables to greater or lesser degrees.

Effect of humidity and water vapour on coax cables: One of the main issues with coax cable with regard to the environment in which it operates is the ingress of moisture. Once it enters the coax it significantly degrades its performance, rendering it unserviceable. It then needs to be replaced.
Moisture ingress causes two main effects that give rise to an increase in the level of attenuation or loss in the cable.
- Increase in resistive loss: The first is an increase in resistive loss arising from oxidation of the braid that gives rise to an increase in the resistance of the braid or outer conductor in the coax cable.
- Moisture in the dielectric: The second is an increase in the loss arising in the dielectric. Water absorbed into the dielectric heats up when power is passed along the coax cable. This heat is as a result of power loss in the cable.
Water vapour, or even water itself can enter the coax cable through a number of ways:
- Moisture entry through coax cable termination The most obvious method of humidity entering a coax cable is through the termination. One very good example is the small termination box provided with many TV antennas. When used externally these termination enclosures provide little protection against the elements and the coax will quickly deteriorate. Even when a connector is used to terminate the coax cable there will be problems if the coax is used externally. Very few connectors are weather proofed, and even if they are supposedly weatherproof, then it is wise to take additional precautions.
  
  Normally the best method is to use self-amalgamating tape. This tape comes in the form of a roll and appears like thick PVC tape but it has a thin paper backing on one side to keep each layer separate and prevents it amalgamating with itself before use. It is used in a similar way to insulating tape. The backing strip is peeled off and then it is wrapped around whatever it is to be waterproofed - in this case a coax cable termination - overlapping each winding by about 50% of its width to ensure a good seal. When applying the tape keep it stretched so that it is applied under tension. Also it is best to start from the thinner end of the job, i.e. where the diameter of whatever it is being applied to is smallest. Where there is a connector on a cable, start on the cable and work towards the connector. Also when winding ensure that there are no holes of voids in which water could condense or enter. Keep the self-amalgamating tape in intimate contact with whatever it is to be waterproofed.
- Moisture entry though pin holes in coax cable jacket Most coax cables have some small holes in their jacket along their length. It is therefore quite possible that moisture will enter through any imperfection in the coax cable jacket. If the pin holes are located externally where they can be affected by the weather then moisture will enter. Unfortunately it is very easy for small abrasions to occur during the installation of a cable and these can include small pin holes right through the jacket. Great care must therefore be taken when installing a cable, and in particular when the coax cable is passed trough a wall or other barrier.
- Water vapour transmission through the coax cable jacket All materials exhibit a finite vapour transmission rate. Accordingly if a coax cable is constantly in contact with moisture, then this will permeate through the jacket. In view of this coax cable should never be buried directly in the ground. Either use some external protection such as a waterproof pipe, and ensure that no water enters it so that small patches of water form in it. Alternatively use the "bury direct" cables that are available. It is also found in airborne applications that the large temperature extremes encountered cause water condensation in the coax cables. This moisture can collect in low areas of the cable causing local areas of corrosion. One method of overcoming this is to fill any voids in the aircraft where coax cable are carried with non-hardening moisture-proof compound.
Effect of sunlight on coax cables: Sunlight has an effect on many substances including plastics, causing them to deteriorate, particularly if they are constantly exposed. The jackets or sheaths around coaxial cable are no exception. It is particularly the ultra-violet light that causes the degradation to the cables. To increase the life of coax cables, manufacturers use high molecular weight polythene. The standard, polyvinylchloride (PVC) jackets exhibit less than half the life expectancy of the high molecular weight polythene.
Effect of corrosive vapours on coax cables Corrosive liquids and vapours can cause problems to coax cables. Even city gases or salt water (an issue on sea going vessels that might have radio equipment) can be an issue. These can speed the deterioration of coax cable quite considerably.

The use of tin or silver coatings can provide some additional protection but this is not permanent. To overcome coax cable environmental issues in these circumstances it is recommended that specially environmentally hardened cables be used where extreme conditions are anticipated.

Coax cables are one of the most robust forms of RF cable or feeder. They can be used in a variety of different situations, but to ensure the longest operational life it is necessary to ensure that the environmental conditions to which they are exposed will not cause any undue degradation in performance. By understanding the environmental limitations it is possible to put a few safeguards in place and ensure the longest life for the RF cable.